Pyro Industries Quest Plus Instrukcje Operacyjne Pobierz pdf (Strona 8)

Stove Operating Controls

Start Switch

The push-bunon START switch activates the convection blower

and the combustion blower. If the exhaust does not reach operating temperature

within 30 minutes, the stove will automatically shut down. The blowers can be

restarted by pushing the START switch again.

"3r-,.,

Auger On/OffSwitch -The AUGER ON/OFF switch activates the fuel feed

(auger) motor only. The START switch has to be activated to give power to the

AUGER

ON/OFF SWITCH. When the AUGER ON/OFF SWITCH switch

turned

off, the fuel feed will stop and the blowers will continue to operate until the stove

has cooled down sufficiently

(up to 45 minutes); then the stove blowers will

automatically turn off.

Heat

Output

Switch

When on manual operation, the HEAT OUTPUT switch

provides the ability to burn at five burn rates. Pressing the heat output switch will

increase the setting by one position. (After setting

#5 it will revert to

#I).

The

HEAT OUTPUT switch alters the fuel feed rate and the combustion air supply

simultaneously. The control

preset to provide the optimum ratio of fuel and air

,,:a?>,

.:.

at each setting.

Thermostat Operation -While on thermostat operation, the stove operates under

,.,

two senings. There

a "pilot" (low) sening and a "demand" (high) setting. If your

thermostat senses the room heat to be higher than your selected temperature, the

thermostat will set the stove to the "pilot" or low setting. This

equivalent to

physically setting the stove on HEAT OUTPUT setting

#l.

If your room tempera-

ture is lower than the selected thermostat temperature, the thermostat will operate

,AI<:I.:u

the stove at the HEAT OUTPUT switch sening you have manually selected. Use a

HEAT OUTPUT switch setting from

through

#5.

The heat output light will

flash on and off during thermostat operation.

;.rl

Auger "On" Light

The red light on the control panel indicates that there

r,3,-.

power to the auger motor. Under normal operation, this light will blink

on and off.

Blower Speedswitch -This button on the control panel controls the

"'x'R!Ii"!'$7RIFS

speed of the convection fan. Turning up the fan will increase the amount of heat

Control Board

into the room. For the best efficiency use the maximum blower speed when high

heat output settings are used. The control will limit the blower settings to

at heat output settings

respectively. In other words, when heat output is set to

the blower will scroll

through speeds

3,4

and

Combustion Fan Trim -The Combustion Fan Trim is located just above the Heat Output Selector switch. Turning

the Trim Control counterclockwise will decrease the amount of combustion air entering the burn grate. Turning the

control clockwise will increase the amount of combustion air entering the burn grate. The Trim Control

factory set

at the

(0) position.

Auger Trim Control-The Auger Trim Control

located just above the Auger OnIOff switch. Turning the Trim

Control counterclockwise will decrease the amount of fuel delivered to the burn grate. Turning the control clock

wise will increase the amount of fuel delivered to the burn grate. The trim control

factoiy set at the (0) position.

Convection Fan Trim -The convection fan trim

located on the backside of the control panel. This can be used

to eliminate fan noise by trimming fan speed slightly above or below a noise band. It can also increase air circula-

tion velocity on

setting if required.

NOTE:

recommended that the damper be used to fine tune your stove to your particular fuel

installation,

(see

page

8).

It is also recommended that you contact your Whitfield Dealer before adjusting the combustion,

convection or auger trim controls.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 39 40

Komentarze do niniejszej Instrukcji

Brak uwag

Pyro Industries Quest Plus Instrukcje Operacyjne Strona 8

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Piece Pyro Industries Quest Plus